![]() ![]() The Altum-PT sensor kit with DJI SkyPort comes with:ĬRP 2 A new compact version of our Calibrated Reflectance Panel. However, integration with DJI M210 RTK drone has not been validated, therefore we cannot ensure compatibility. This sensor kit comes ready to integrate with DJI SkyPort compatible drones (Matrice 300, Matrice 200 V2, and Matrice 210 V2). Altum-PT also features a global shutter for distortion-free results, open APIs, and a new storage device allowing for up to 2 captures/second. It seamlessly integrates an ultra-high-resolution panchromatic imager, a new thermal imager that provides twice the ground resolution of the previous Altum, and five discrete spectral bands, allowing plant-level applications such as early-stage stand counting. Also, we recommend setting the speed sliders to Fast except for few cases where the pictures sharpness is not satisfying because of the drone speed, for example when flying at low altitude.Product Details: Altum-PT Sensor Kit with DJI SkyPortĪltum-PT is an optimized 3-in-1 solution for advanced remote sensing and agricultural research. Note that those speed intervals calculations depend on the drone and it will not always be the same. However, if you set it to the second interval after slow (5.2 m/s) then your drone will actually fly at 5.2 m/s instead of 6.2 m/s. As an example, if the drone speed calculation of your flight is 6.2 m/s, setting up the speed sliders in the middle (8.5 m/s) will have no impact. Note that using the speed slider, the speed of your drone will be impacted only in some conditions. Then the 3 intervals in between are evenly split between 2m/s and 15 m/s meaning that the speeds will be as follow: If changes occur about the support of this drone we will communicate for now, no decision has been taken about the potential use of Pix4Dcapture with the P4P RTK as some exchange are still in progress with DJI about drone speed during the acquisition is calculated and set depending on your flight parameters (overlap, flight height).įor most of the drones, the minimum speed corresponding to Slow is 2 m/s and the maximum corresponding to Fast is 15 m/s. Using Safe mode and defining the custom camera (without defining any time-lapse), pictures might be triggered automatically at the defined waypoints.Ībout your second question, yes Pix4Dcapture will be able to it is not in our pipeline to support officially the Phantom 4 Advanced (P4A). However, some users tried to test it and sometimes with good success. You can have a look at this thread on our community website. Note that you will have to activate a time-lapse in the drone manufacturer app as the camera cannot be controlled by Pix4Dcapture. The important step is to have the same timelapse defined in Pix4Dcapture and in the manufacturer app. Quit the manufacturer application, open Pix4Dcapture and set a custom camera. It won't be possible to make it work if the option is not available. In DJI manufacturer app (DJI GO, DJI GO4), set a timelapse if the option is available. We would be glad to have feedback from users trying these methods. However, on iOS, as a workaround, you can try the following but we can not make any guarantee that it will work as we did not test it. There is no way to easily change that in our application. ![]() Your app are very stable and usefull, I think this option will be very interesting for users that avoid another loaded apps, like dronedeploy.īest Regards, Comment actions default, Pix4Dcapture will take the X5S with 15mm focal length parameters. I think that option will reach a lot of users that own P4A. ![]() Maybe the Pix4D can release a version "beta" of Pix4DCapture, for users interested in test with P4A, accepting all the terms and responsabilities like beta-testers, even because, the status in this listing is "Not Tested". I tried to configure in Pix4DCapture the model "Phantom 4 Pro", but when I connect the drone P4A, the options returns to "Phantom 4"Īnd I can't use the 20Mpixel from native P4A. (add P4A and P4P to compare, and hide dupplicated details) How you can check the configuration in DJI site, the P4A is very similar to the P4P (DJI Phantom 4 Pro), differencing basically by avoindance sensors and some improvements in datalink, see: Hi, there are some prevision to support P4A (DJI Phantom 4 Advanced)? The drone to be selected before starting a mission should be one of those having the same connection mode (Wi-Fi or USB cable). Recommendations to fly a drone that was not tested Compatible only with RGB (4.7.0 and later)Ĭompatible - Not tested (4.10.0 and later) ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |